Factory Install Only Package includes: - (1) CAT 40 Friction Stir Weld Tool Holder - (3) Recommended Friction Stir Weld H13 pin tools. (1) 1/8”, (1) 3/16”, (1) 1/4” - Friction Stir Weld Machine Preparation - Friction Stir Weld Viewer Software - Friction Stir Weld Operating Manual - Mazak MegaStir voice and email technical support - Mazak MegaStir 3 days on-site training including travel expenses in CONUS NOTE: Tooling is for aluminum welding only. NOTE: If the customer wants different tooling/pins than the listed recommendations, an engineering request is required for review by engineering. NOTE: Additional training is available at additional cost. NOTE: If the customer uses Friction Stir Weld Viewer Software, customer-provided external PC or MT Tablet is required.

Includes: Grease spindle, Roller guide seals, Grease to Oil Ways, CRT and SFI air purge, Enhanced Dust collector prep. **NOTE: Price includes credit for coolant system delete

GRAPHITE PACKAGE INCLUDING DONALDSON DFO 1-1

NC ROTARY TABLE PACKAGE INCLUDES: - Servo Motor And Servo Amplifier - Piping And Hoses For Clamp Mechanism - Electrical I/F

NC ROTARY TABLE PACKAGE INCLUDES: - Servo Motor And Servo Amplifier - Piping And Hoses For Clamp Mechanism - Electrical I/F

NC ROTARY TABLE PACKAGE INCLUDES: - Servo Motor And Servo Amplifier - Piping And Hoses For Clamp Mechanism - Electrical I/F

NC ROTARY TABLE PACKAGE INCLUDES: - Servo Motor And Servo Amplifier - Piping And Hoses For Clamp Mechanism - Electrical I/F

NC ROTARY TABLE PACKAGE INCLUDES: - Servo Motor And Servo Amplifier - Piping And Hoses For Clamp Mechanism - Electrical I/F

NOTE: Only available on Mazak supplied Rotary tables only

NOTE: Only available on Mazak supplied Rotary tables only

Includes: - Clamp/Unclamp Control - Part Seat Confirmation Note: This is electrical I/F only and does not include any mechanical prep. or fixture.

FIXTURE PREPARATION - SIX PORT PNEUMATIC

FIXTURE PREPARATION - SIX PORT PNEUMATIC

*Customer/Integrator's responsibility to conform to standard interface, and integrate their equipment. * I/O map available after order. * Does not include modifications during installation. * Does not include integration support.

ADVANCE robot interface improvements over BASIC: * Can minimize E-Stop area affected. * Allows high speed machine movement with door open during robot service (Lathes) * Customer/Integrator's responsibility to conform to standard interface, and integrate their equipment. * I/O map available after order. * Does not include modifications during installation. * Does not include integration support. * Integration support not available.

19" COLOR LCD (TOUCH SCREEN)

NO635D650C0

Includes: - EIA DYNAMIC COMPENSATION 2 (INCLUDES EIA DYNAMIC COMPENSATION 1)

Smooth Screen can be synchronized on mobile device. (Smart Phone / Tablet). Customer own mobile device can be used as a sub monitor of Smooth CNC.

NOTE: Extended Card can be used to connect CNC to field network (sequencer, remote IO).

NOTE: Extended Card can be used to connect CNC to field network (robot, sequencer, remote IO).

Allows the base units of a machine to be changed between inch and metric units.

Installing the CYLINDER option enables the interpolation milling commands G07.1 and G12.1 to be utilized. Option #38 on control option page. Notes and Cautions: If G07.1 or G12.1 is commanded without the CYLINDER option installed, ALARM 936 NO OPTION FOUND will occur. Option #21 POLAR COORDINATES INPUT does not enable the use of command G12.1

This option allows the programmer to temporarily shift the workpiece origin to a new location using any combination of X, Y, Z and make that the active cutting plane. G68 G-Code is used.

A software option to allow the controller to output status and process data in a common and open format called MTConnect. (ANSI/MTC1.4-2018 MTConnect StandardV1.4 12/7/2018). MTConnect has become a popular means of data collection for ERP, MES, and OEE systems. Includes MTCONNECT Agent with installation.

This Windows App displays current status of all MTConnect compliant machines. Shows only static data. No calculations (ie Utilization, OEE, etc) Great for factory dashboard. This is intended as an operator self-management tool.

Includes the following High-Performance functionality: - New GUI with special HP conveyor screen on the Ez control. - Inverter control for Forward/Reverse motion. - Variable Speed Function (3 speeds: High, Medium, & Low) - Intermittent Operation Function - Overload Detection Function. Conveyor will automatically reverse direction once load is detected and then return to forward direction after a period of time. - Synchronized Auto Operation Function. Conveyor automatically turns on/off when used

Includes the following High-Performance functionality: - New GUI with special HP conveyor screen on the Ez control. - Inverter control for Forward/Reverse motion. - Variable Speed Function (3 speeds: High, Medium, & Low) - Intermittent Operation Function - Overload Detection Function. Conveyor will automatically reverse direction once load is detected and then return to forward direction after a period of time. - Synchronized Auto Operation Function. Conveyor automatically turns on/off when used

Includes the following High-Performance functionality: - New GUI with special HP conveyor screen on the Ez control. - Inverter control for Forward/Reverse motion. - Variable Speed Function (3 speeds: High, Medium, & Low) - Intermittent Operation Function - Overload Detection Function. Conveyor will automatically reverse direction once load is detected and then return to forward direction after a period of time. - Synchronized Auto Operation Function. Conveyor automatically turns on/off when used

Note: Requires manual cylinder position/angle adjustment. Up to a 6" maximum stroke for air nozzle.

Note: Air nozzle can be programmed to rotate to specific angular positions for each tool. Up to a 6" maximum stroke for air nozzle. Air nozzle can be used in conjunction with or without programmable coolant.

NOTE: Price is for machine without through spindle coolant option.

NOTE: Price is for machine that has the through spindle coolant option. This option cannot be used simultaneously with the through spindle coolant option.

95 Gallon Coolant Pan is recommended NOTE: IF 213 PSI IS REQUIRED AN ENGINEERING REQUEST MUST BE SUBMITTED. ELECTRICAL PREP IS INCLUDED IN THE PRICE.

95 Gallon Coolant Pan is recommended

Note: If this option is selected with cover coolant and superflow, the 95 gallon coolant tank option is required

NOTE: Requires the 95 Gallon Coolant Pan Option (CS840)

NOTE: Required when the Niagara Coolant option (CS300) is selected

*NOTE: Requires 100-120V power supply

Mazak SuperFlow S8 / 1000 single outlet, fixed high pressure coolant system (1000psi/8gpm measured at the pump) including one high-capacity bag filter vessel.

Mazak SuperFlow T8 / 1000 single outlet, fixed high pressure coolant system (1000psi/8gpm measured at the pump) including two high-capacity bag filter vessels.

Mazak SuperFlow V8M / 1000 single outlet, variable high pressure coolant system (200psi - 1000psi/8gpm measured at the pump) including dual high-capacity bag filters with manual cross over.

Mazak SuperFlow C8 / 1000 single outlet, fixed high pressure coolant system (1000psi/8gpm measured at the pump) including Single Bag Type Filter for cyclonic filter sediment only. The coolant will be filtered by the cyclonic filter only and this is not a crossover type filter system.

Mazak SuperFlow V8A / 1000 single outlet, variable high pressure coolant system (200psi - 1000psi/8gpm measured at the pump) including dual high-capacity bag filters with auto-cross over.

NOTE: THIS PACKAGE INCLUDES THE RENISHAW WIRELESS OTS-AA TOOL SETTER WITH ROTATING TOOLSETTING SOFTWARE CABABLE OF SETTING LENGTH, DIAMETER, AND DETECTING BROKEN TOOLS. THIS PACKAGE ALSO INCLUDES THE PREP FOR MAZAL MONITORING SYSTEM B OPTICAL OMP60 WITH INSPECTION PLUS SOFTWARE.

NOTE: INCLUDES RENISHAW OMI-2T DUAL PROBE OPTICAL RECEIVER, OMP60 OPTICAL PROBE (AA BATTERY), WIRELESS OTS-AA TOOLSETTER, INSPECTION PLUS SOFTWARE, AND ROTATING TOOL SETTING SOFTWARE.

NOTE: INCLUDES RENISHAW RMP600 RADIO PROBE, TOOLSETTER, INSPECTION PLUS SOFTWARE, AND ROTATING TOOL SETTING SOFTWARE.

Factory Install Only INCLUDES RENISHAW RMP60 RADIO PROBE, TOOLSETTER, INSPECTION PLUS SOFTWARE, AND ROTATING TOOL SETTING SOFTWARE NOTE: THIS PACKAGE DOES NOT INCLUDE TRAINING BY RENISHAW. NOTE: Package does not include Set & Inspect with SmoothEZ CNC. See Probing packages with the MT Tablet option. NOTE: Package includes Set & Inspect with SmoothG CNC.

Package includes MT Tablet, Set & Inspection software, & Mazak Smooth Link

Package includes MT Tablet, Set & Inspection software, & Mazak Smooth Link

Package includes MT Tablet, Set & Inspection software, & Mazak Smooth Link

INCLUDES: 2 days onsite training by Renishaw and Calibration Tool. SPECIAL NOTE: For installation in Mexico add $2,000.

Note: For use with 12,000/15,000 rpm spindle option

Note: For use with 12,000/15,000 rpm spindle option

Note: For use with 20,000 rpm spindle option

Note: For use with 20,000 rpm spindle option

NOTE: This is in place of the standard USB Manual

Note: On-site applications support is offered for basic applications assistance and on-site training only. - A minimum of three consecutive days is recommended, but no more than a maximum of five days unless approved by the regional Mazak Applications Manager. If additional on-site application support is required beyond the maximum, please consult with the regional Mazak Applications Manager to review and confirm actual requirements to determine total cost estimates including additional travel and living expenses. - This cost is for on-site support only. It is not to be used to quote or provide part / process specific programming, machine Runoffs, or Teamkey / Turnkey proposals. Please consult with the regional Mazak Applications Manager if a proposal for these types of additional services is required. - On-Site Applications support requires machine installation sign off (form #238) to be completed prior to applications assistance taking place. Please also note that On-Site Applications support must be scheduled and completed within 6 months of machine installation sign-off.

INCLUDES: SB2WMTDIPC SmartBox for connecting up to ten (10) machines (Connections may be limited depending on size and frequency of data). The final security configuration is determined and set by the end user. Capable to operates on a standard 110-120V (60 Hz) wall outlet. (Power provided by end user) **NOTE: Does not include MT Connect Adapter. Must be ordered separately. Additional MTConnect Adapters required for multiple machines (Not included) Floor stand can be purchased separately. NOTE: Provides network connectivity, network isolation, MTConnect communications (Read Only), and I/O. Allows expansion for future IOT solutions (Edge Analytics, etc.) **See the Implementation Guide for more details.